92.5 mhz saw filter 1.7 mhz bandwidth part number SF0092CD02326S spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0092CD02326S rev a 22-feb-201 0 ecn 36650 page 1 of 3 description ? 92.5 mhz saw bandpass filter with 1.7 mhz bandwidth. ? 13.3 x 6.5 mm ceramic lcc package. ? rohs compliant. typical performance horizontal: frequency : 2 mhz/div vertical: relative magnitude : 10 db/div relative magnitude : 1 db/div phase linearity : 5 deg/div group delay : 100 ns/div s11 (82.5-102.5 mhz) s22 (82.5-102.5 mhz)
92.5 mhz saw filter 1.7 mhz bandwidth part number SF0092CD02326S spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0092CD02326S rev a 22-feb-201 0 ecn 36650 page 2 of 3 specification parameter min typ max units center frequency (fc) 1 - 92.50 - mhz insertion loss at 92.5 mhz 17 18.2 22 db amplitude ripple (91.65 to 93. 35 mhz) - 0.5 0.7 db p-p lower 0.7db band edge frequency 3 - 91.57 91.65 mhz upper 0.7db band edge frequency 3 93.35 93.52 - mhz lower 15db band edge frequency 3 90.50 90.63 - mhz upper 15db band edge frequency 3 94.42 94.50 mhz lower 40db band edge frequency 3 89.5 90.1 - mhz upper 40db band edge frequency 3 - 94.9 95.5 mhz lower sidelobe attenuation (78-82 mhz) 45 50 - db upper sidelobe attenuation (97.5-122.5 mhz) 45 50 - db triple transit suppression 40 50 - db group delay ripple (91.65 to 93.35 mhz) 2 - 75 90 ns p-p system source and load impedance - 50 - ohm ambient temperature - 25 - c notes: 1. center frequency: fc = (lower 15db value + upper 15db value)/2. 2. a smoothing aperture of 150 kh z may be applied to this measurement. 3. measured relative to the insertion loss value. maximum ratings parameter min max units storage temperature range -40 85 ? c operating temperature range 10 70 ? c input power level - 13 dbm matching circuit typical component values: ls1 = 400 nh ls2 = 420 nh cp2 = 56 pf notes: 1. recommend 2% tolerance matching components. typical inductor q=40. 2. values shown are for reference only and may change depending on board layout. 11 5 12 6 input 50 ? single ended output 50 ? single ended gnd gnd
92.5 mhz saw filter 1.7 mhz bandwidth part number SF0092CD02326S spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0092CD02326S rev a 22-feb-201 0 ecn 36650 page 3 of 3 package outline suggested footprint all specifications are believed to be accurate and reliable. howe ver, spectrum microwave reserves the right to make changes wit hout notice. ? 2010 all rights reserved. iso 9001 registered package material: body: al 2 o 3 ceramic lid: kovar, ni plated terminations: au plating 1 m min, over a 1.3-8.9 m ni plating units: mm tolerances are typically 0.15 mm except where indicated. pad configuration: input: 11 input return: 12 output: 5 output return: 6 case ground: all other pads
|